CNC Bender v10-20070828 - Revision history

Mcone at 23:46, 20 September 2007

2007-09-20T23:46:46Z

2007-08-29T15:30:03Z

‎First Installed To Benders

2007-08-29T04:51:04Z

‎Proper Clearance in all Radius Shift Modes

2007-08-29T04:49:46Z

‎IN AUTO MODE

2007-08-29T04:48:38Z

‎Solution To Issue

2007-08-29T04:47:41Z

‎IN STEP MODE

2007-08-29T04:47:08Z

‎IN STEP MODE

2007-08-29T04:45:43Z

‎Explanation of Issue

2007-08-29T04:33:21Z

‎IN STEP MODE

2007-08-29T04:32:41Z

‎Solution

@@ Line 1: / Line 1: @@
-[[image:Cncbender.jpg|thumb|CNC Bender User Interface for ProControl]]
+[[image:Cncbender.jpg|thumb|300px|CNC Bender User Interface for ProControl]]
+[[image:cncbender_logo.jpg|400px]]
 __TOC__

← Older revision		Revision as of 15:30, 29 August 2007
Line 80:		Line 80:
	=First Installed To Benders=		=First Installed To Benders=

−	*	+	*SMT 19144 - Right Hand VB300 Bender - Triple Radius Head Shifter

← Older revision		Revision as of 04:51, 29 August 2007
Line 71:		Line 71:
	The end effect of this change is that both STEP and AUTO modes will now treat the [[Post Bend Jog]] identically even when the [[Radius Shift Mode]] is set to During Feed.		The end effect of this change is that both STEP and AUTO modes will now treat the [[Post Bend Jog]] identically even when the [[Radius Shift Mode]] is set to During Feed.

−	~~<br>~~
−	~~If the tube does not crash in the dies during AUTO mode, then it will not crash in the dies in STEP mode.~~

	<br>		<br>

@@ Line 39: / Line 39: @@
 ====IN AUTO MODE====
-# The [[Post Bend Jog]], even though placed after the activation of the secondary DURING FEED radius shifting process,  can still appear to occur on the bender just ''before'' the the simultaneous radius shifting occurs due to delays in startup of the radius shift secondary process.
+# The [[Post Bend Jog]], even though placed after the activation of the secondary DURING FEED radius shifting process,  can still appear to occur on the bender at the same time the radius shifting occurs due to delays in startup of the radius shift secondary process.
 # This makes operators believe that the [[Post Bend Jog]] is activated first - even though it was not.
 # This is especially true if a [[Radius Shift Delay]] is set to greater than zero milliseconds.

@@ Line 54: / Line 54: @@
 ==Solution To Issue==
-The [[Post Bend Jog]] will now always be placed '''BEFORE''' the start of any "DURING FEED" radius shifting.  This is a sample process list with the new order:
+The [[Post Bend Jog]] will now always be placed '''BEFORE''' the start of any radius shifting.  This is a sample process list with the new order:
@@ Line 79: / Line 79: @@
 </ul>
 =First Installed To Benders=
+*

@@ Line 48: / Line 48: @@
 ====IN STEP MODE====
 # The [[Post Bend Jog]] move would effectively disappear during STEP mode.
-# In Step mode, the DURING FEED radius shifting would already be completed before the [[Post Bend Jog]] would be activated - because STEP mode pauses after the radius shifting starts, but before the [[Post Bend Jog]]
+# In Step mode, the DURING FEED radius shifting would already be completed before the [[Post Bend Jog]] would be activated - because STEP mode pauses the process after the radius shifting starts, but before the [[Post Bend Jog]] begins
 # This would create a crash condition where the radius shifting would occur with the tube still in the [[bend die]].
 <br><br>

@@ Line 36: / Line 36: @@
 </pre>
-Why is this a problem?  Compare what happens in the two scenarios listed below (AUTO and STEP).  Note how the end result is different in STEP than in AUTO even though the command order (as shown above) is not changed.
+But this created a problem.  Compare what happens in the two scenarios listed below (AUTO and STEP).  Note how the end result is different in STEP than in AUTO even though the command order (as shown above) is not changed.
 ====IN AUTO MODE====

← Older revision		Revision as of 04:32, 29 August 2007
Line 53:		Line 53:


−	===Solution===	+	==Solution To Issue==

	The [[Post Bend Jog]] will now always be placed '''BEFORE''' the start of any "DURING FEED" radius shifting. This is a sample process list with the new order:		The [[Post Bend Jog]] will now always be placed '''BEFORE''' the start of any "DURING FEED" radius shifting. This is a sample process list with the new order: