CNC Bender Seam Detection - Revision history

Mcone: /* Seam Detect Mode in PreBend Dynamic Options */

2009-06-13T02:04:23Z

‎Seam Detect Mode in PreBend Dynamic Options

2009-06-13T01:37:39Z

‎Sample of How Used

2009-06-13T01:36:38Z

‎SEAM DETECT MODE DYNAMIC OPTION

2009-06-13T01:36:01Z

‎SEAM DETECT MODE DYNAMIC OPTION

2009-06-13T01:32:26Z

‎25px NEW: CIOs and COMDEFs

2009-06-13T01:25:34Z

‎25px NEW: INTERNAL COMMANDS '''[direct_axis_jog]''' and '''[direct_axis_jog_halt]'''

2009-06-13T01:25:18Z

‎SEAM DETECT MODE DYNAMIC OPTION

2009-06-13T01:24:56Z

‎BUILT IN - SEAM DETECT MODE DYNAMIC OPTION

2009-06-13T01:24:43Z

2009-06-13T01:24:19Z

‎25px NEW - Seam Detect Mode in PreBend Dynamic Options

@@ Line 4: / Line 4: @@
 __TOC__
 ===Seam Detect Mode in PreBend Dynamic Options===
@@ Line 19: / Line 21: @@
 <br><br>
 Then the main process detects that the seam detect input is ACTIVE and  moves to the next step (See "3" in the orange box).<br>
 ===SEAM DETECT MODE DYNAMIC OPTION  ===

@@ Line 64: / Line 64: @@
 <pre>
-[direct_axis_jog] servo_controller_module_1, 2, 1
+[direct_axis_jog] servo_233, 2, 1
 [if] and, input=Input_SeamDetect_End
    // Seam detected - Disable the rotate jog now
    [direct_axis_jog_halt]
-   [SECONDARY_PROCLIST] seam_detect, disable
+   [SECONDARY_PROCLIST] seam_detect_rotate_axis, disable
 [end]
 </pre>

@@ Line 32: / Line 32: @@
 If enabled, the commands for seam detection are added to the process list between the chuck close and the run button logic.  This is a sample of what is inserted.  (What you see here represents the commands for STEPS 1 and 2 in the orange box in the image above.)
 <br><br>
-[[image:cncbender_seamdetect_rotateaxis_processcode.jpg|400px]]
+[[image:cncbender_seamdetect_rotateaxis_processcode.jpg]]
 <br><br>

@@ Line 32: / Line 32: @@
 If enabled, the commands for seam detection are added to the process list between the chuck close and the run button logic.  This is a sample of what is inserted.  (What you see here represents the commands for STEPS 1 and 2 in the orange box in the image above.)
 <br><br>
-[[image:seamdetect_processlist.jpg]]
+[[image:cncbender_seamdetect_rotateaxis_processcode.jpg|400px]]
 <br><br>

@@ Line 75: / Line 75: @@
 The jog command rotates the 2nd axis of the first servo module in the positive direction.  This is the rotate axis.  The motion continues until the seam detect input activates.  At that point the jog is halted with the second command, and the secondary processlist disables itself.
-===[[image:Check.jpg|25px]] NEW: CIOs and COMDEFs ===
+===Seam Detection CIOs and COMDEFs ===
-# '''Input_SeamDetect_End''' is a standard CIO added for this feature.
+====CIO====
-# '''WaitForSeamDetect''' is the name used for the new COMDEF in the main process list that waits for the seam detect to go active.
+# '''Input_SeamDetect_End''' - Is the input set by the seam detect's output when the seam is found
 <br><br>

@@ Line 37: / Line 37: @@
 The new "seam_detect_rotate_axis.cncprocesslist" is a secondary multitasking processlist that is configurable to work with the application.
-===[[image:Check.jpg|25px]] NEW: INTERNAL COMMANDS  '''[direct_axis_jog]''' and '''[direct_axis_jog_halt]''' ===
+===INTERNAL COMMANDS  '''[direct_axis_jog]''' and '''[direct_axis_jog_halt]''' ===
 ==== [direct_axis_jog] ====
@@ Line 74: / Line 74: @@
 The jog command rotates the 2nd axis of the first servo module in the positive direction.  This is the rotate axis.  The motion continues until the seam detect input activates.  At that point the jog is halted with the second command, and the secondary processlist disables itself.
 ===[[image:Check.jpg|25px]] NEW: CIOs and COMDEFs ===

← Older revision		Revision as of 01:24, 13 June 2009
Line 22:		Line 22:


−	===~~BUILT IN -~~ SEAM DETECT MODE DYNAMIC OPTION ===	+	===SEAM DETECT MODE DYNAMIC OPTION ===

	The new feature can be switched on with the Seam Detect option in the PreBend option:<br><br>		The new feature can be switched on with the Seam Detect option in the PreBend option:<br><br>

← Older revision		Revision as of 01:24, 13 June 2009
Line 21:		Line 21:


−	~~See [[CNC Bender Seam Detect]] for details.~~

−	===~~[[image:Check.jpg\|25px]] New:~~ BUILT IN - SEAM DETECT MODE DYNAMIC OPTION ===	+	===BUILT IN - SEAM DETECT MODE DYNAMIC OPTION ===

	The new feature can be switched on with the Seam Detect option in the PreBend option:<br><br>		The new feature can be switched on with the Seam Detect option in the PreBend option:<br><br>

← Older revision		Revision as of 01:24, 13 June 2009
Line 5:		Line 5:


−	===~~[[image:Check.jpg\|25px]] NEW -~~ Seam Detect Mode in PreBend Dynamic Options===	+	===Seam Detect Mode in PreBend Dynamic Options===

	[[image:Seamdetect_application.jpg\|300px]]		[[image:Seamdetect_application.jpg\|300px]]