CNC Bender 10.0.6.0i - SVout Export Feature - Revision history

Jesralian: /* NEW TIME SAVER - SVout EXPORT FEATURE */

2006-11-02T14:34:05Z

‎NEW TIME SAVER - SVout EXPORT FEATURE

Jesralian: /* NEW TIME SAVER - SVout EXPORT FEATURE */

2006-11-02T14:31:05Z

‎NEW TIME SAVER - SVout EXPORT FEATURE

Jesralian at 14:27, 2 November 2006

2006-11-02T14:27:22Z

Jesralian at 14:25, 2 November 2006

2006-11-02T14:25:19Z

Jesralian at 14:11, 2 November 2006

2006-11-02T14:11:21Z

New page

==NEW TIME SAVER - SVout EXPORT FEATURE==

CNC Bender can now output master SV data. This means that MASTER FILE TRANSFER CAN OCCUR IN BOTH DIRECTIONS in CNC Bender.

If master data is initially entered in CNC Bender, then SV file can be exported, then picked up by the ROMER computer for use directly in Supravision - all through the network. This will save time for customers that prefer to avoid entering data multiple times.

The SVout button in the XYZ Data page is new:

It exports part number, unit setting, XYZ data, FRB data or FRB + Adjustments, diameter, and cut length.

The SVout feature handles export with a lot of sophistication:

The operator chooses if he wants XYZ data alone, or XYZ + FRB data, or XYZ + FRB + Adjustments in the file. The FRB data is converted to Corrected LRA values.

Avoidance move rows with zero degree bend angles are compressed into other true bend rows. This means that avoidance data will be properly removed from the LRA data so that the Supravision software will not be confused.

CNC Bender reports what was exported after the export is complete.

@@ Line 3: / Line 3: @@
 [[CNC_Bender|CNC Bender]] can now output master SV data.  This means that MASTER FILE TRANSFER CAN OCCUR IN BOTH DIRECTIONS in CNC Bender.
-If master data is initially entered in CNC Bender, then  SV file can be exported, then picked up by the ROMER computer for use directly in Supravision - all through the network.  This will save time for customers that prefer to avoid entering data multiple times.
+If master data is initially entered in CNC Bender, then  SV file can be exported, then picked up by the ROMER computer for use directly in [[Supravision]] - all through the network.  This will save time for customers that prefer to avoid entering data multiple times.
 The SVout button in the XYZ Data page is new (see right image)
-[[Image:CNC_Bender_SV_Out.jpg|frame|The new SV Out button on CNC Bender's XYZ Coord Data Page]]
+[[Image:CNC_Bender_SV_Out.jpg|frame|The new SVout button on CNC Bender's XYZ Coord Data Page]]
 It exports part number, unit setting, XYZ data, FRB data or FRB + Adjustments, diameter, and cut length.
-The SVout feature handles export with a lot of sophistication:
+===Sophistication of SVout Export===
 The operator chooses if he wants XYZ data alone, or XYZ + FRB data, or XYZ + FRB + Adjustments in the file.  The FRB data is converted to Corrected LRA values.

← Older revision		Revision as of 14:27, 2 November 2006
Line 17:		Line 17:

	CNC Bender reports what was exported after the export is complete.		CNC Bender reports what was exported after the export is complete.
		+	[[Image:Supravision_Export_Complete.jpg\|none]]

@@ Line 1: / Line 1: @@
 ==NEW TIME SAVER - SVout EXPORT FEATURE==
-CNC Bender can now output master SV data.  This means that MASTER FILE TRANSFER CAN OCCUR IN BOTH DIRECTIONS in CNC Bender.
+[[CNC_Bender|CNC Bender]] can now output master SV data.  This means that MASTER FILE TRANSFER CAN OCCUR IN BOTH DIRECTIONS in CNC Bender.
 If master data is initially entered in CNC Bender, then  SV file can be exported, then picked up by the ROMER computer for use directly in Supravision - all through the network.  This will save time for customers that prefer to avoid entering data multiple times.