CNCProcessor.cfg - Revision history

Mcone: /* Properties Definition */

2009-01-28T21:06:16Z

‎Properties Definition

2009-01-28T21:05:38Z

‎Remarks and Notes in the Configuration File

2009-01-28T21:04:58Z

‎Where to find it on the Hard Disk

2009-01-28T21:04:35Z

‎Example Configuration Setup

2009-01-28T21:04:10Z

‎Where to find it on the Hard Disk

2009-01-28T21:03:58Z

‎Where to find it in CNC Bender

2009-01-28T21:03:43Z

‎Setup in CNCProcessor.cfg File

2009-01-28T21:03:20Z

2009-01-28T20:59:10Z

2009-01-28T20:57:53Z

‎Properties for Older Versions of CNC Bender

@@ Line 97: / Line 97: @@
 ===Properties Definition===
 Read about individual properties:<br>
-These two properties control the [[Auto Lube]] feature:<br>
 [[Machine Lube Duration]]<br>
 [[Lube Machine At Bend Count]]<br>

@@ Line 94: / Line 94: @@
 Note that remarks may be added to the file with lines preceded by double forward slashes.
-<pre>// How long does the machine loop output enable?</pre>
+<pre>// This setting was adjusted by Michael Cone on January 28, 2009</pre>
 ===Properties Definition===

@@ Line 90: / Line 90: @@
 ====Where to find it on the Hard Disk====
 The file is available in the c:\cnc\config folder in the file "CNCProcessor.cfg".  A text editor can be used to change the file.  Only change the file this way when CNC Bender is closed.
 ===Properties Definition===

← Older revision		Revision as of 21:04, 28 January 2009
Line 73:		Line 73:

	</pre>		</pre>
−
−
−	~~Note that remarks may be added to the file with lines preceded by double forward slashes.~~
−
−	~~<pre>// How long does the machine loop output enable?</pre>~~
−
−
	<br>		<br>

@@ Line 95: / Line 95: @@
 Then save the data to disk in order to store the changes made.
-===Where to find it on the Hard Disk===
+====Where to find it on the Hard Disk====
 The file is available in the c:\cnc\config folder in the file "CNCProcessor.cfg".  A text editor can be used to change the file.  Only change the file this way when CNC Bender is closed.
 ===Properties Definition===

@@ Line 86: / Line 86: @@
 <br><br>
-===Where to find it in CNC Bender===
+====Where to find it in CNC Bender====
 The configuration is displayed in an editor in the Low Level menu, CNC Processor CFG tab.<br>

@@ Line 82: / Line 82: @@
 <br>
-=Setup in [[CNCProcessor.cfg]] File=
+===Editing the [[CNCProcessor.cfg]] File===
 The CNC Processor configuration file contains the values necessary to adjust the machine lube settings.
 <br><br>

← Older revision		Revision as of 21:03, 28 January 2009
Line 81:		Line 81:

	<br>		<br>
		+
		+	=Setup in [[CNCProcessor.cfg]] File=
		+	The CNC Processor configuration file contains the values necessary to adjust the machine lube settings.
		+	<br><br>
		+
		+	===Where to find it in CNC Bender===
		+	The configuration is displayed in an editor in the Low Level menu, CNC Processor CFG tab.<br>
		+
		+	[[image:cncbender_cncprocessor_config_file.jpg\|600px]]
		+
		+	If you edit the values in this editor, be sure to keep the equals signs in the setup, and be careful to enter valid values. For example, for duration values, enter only whole numbers (no text).
		+
		+	Then save the data to disk in order to store the changes made.
		+
		+	===Where to find it on the Hard Disk===
		+	The file is available in the c:\cnc\config folder in the file "CNCProcessor.cfg". A text editor can be used to change the file. Only change the file this way when CNC Bender is closed.
		+

	===Properties Definition===		===Properties Definition===

@@ Line 11: / Line 11: @@
 <pre>[Machine Lube]</pre>
-===Example Setup===
+===Property Values===
 This is an example configuration setup: