Ball Probe Setup - Revision history

Mcone at 17:35, 4 September 2015

2015-09-04T17:35:35Z

2015-09-04T17:35:01Z

‎About the Default Ball Probe Setup

2015-09-04T17:34:39Z

‎About the Default Ball Probe Setup

2015-09-04T17:33:59Z

‎About the Default Ball Probe Setup

2015-09-04T17:33:13Z

‎STEP 5

2015-09-04T17:29:57Z

‎STEP 4

2015-09-04T17:27:20Z

‎STEP 3

2015-09-04T17:15:12Z

‎STEP 2

2015-09-04T17:12:20Z

‎About the Default Ball Probe Setup

← Older revision		Revision as of 17:35, 4 September 2015
Line 15:		Line 15:


−	== ~~About~~ the Default Ball Probe Setup==	+	== How to Change the Default Ball Probe Setup==

	The default ball probe setup is always controlled by the FARO drivers and dialogs. The FARO driver dialog windows can be loaded from inside VTube-LASER while VTube is connected to the arm. To change the default ball probe, you will need to access the FARO dialog and choose the correct probe.<br><br>		The default ball probe setup is always controlled by the FARO drivers and dialogs. The FARO driver dialog windows can be loaded from inside VTube-LASER while VTube is connected to the arm. To change the default ball probe, you will need to access the FARO dialog and choose the correct probe.<br><br>

@@ Line 17: / Line 17: @@
 == About the Default Ball Probe Setup==
-The default ball probe setup is always controlled by the FARO drivers and dialogs.  These are windows that can be loaded from VTube-LASER while it is connected to the arm.  To change the default ball probe, you will need to access the FARO dialog and choose the correct probe.<br><br>
+The default ball probe setup is always controlled by the FARO drivers and dialogs.  The FARO driver dialog windows can be loaded from inside VTube-LASER while VTube is connected to the arm.  To change the default ball probe, you will need to access the FARO dialog and choose the correct probe.<br><br>
 '''You must be connected to a FARO arm to perform these steps.'''

@@ Line 17: / Line 17: @@
 == About the Default Ball Probe Setup==
-The default ball probe setup is always controlled by the FARO dialogs.  These are windows that can be loaded from VTube-LASER while it is connected to the arm.  To change the default ball probe, you will need to access the FARO dialog and choose the correct probe.<br><br>
+The default ball probe setup is always controlled by the FARO drivers and dialogs.  These are windows that can be loaded from VTube-LASER while it is connected to the arm.  To change the default ball probe, you will need to access the FARO dialog and choose the correct probe.<br><br>
 '''You must be connected to a FARO arm to perform these steps.'''

@@ Line 3: / Line 3: @@
 <td width=225>
 [[image:vtube-laser_logo_1.96.png|200px]]
 * Back to [[VTube-LASER]]
 </td>
@@ Line 75: / Line 74: @@
 ==Other Pages==
 *Back to the [[VTube-LASER]] page

@@ Line 63: / Line 63: @@
 ===STEP 5===
-Exit the System Options menu.  VTube will now clear to the new settings.
+Observe that the new ball probe selection will appear in the Arm grid.
 </td>
 <td>
-[[image:vtube_v2.2_systemoptions_closemenu.png|400px]]
+[[image:vtube-laser_2.2_measuresetup_menu_6mmball.png|400px]]
 </td>
 </tr>

@@ Line 53: / Line 53: @@
 ===STEP 4===
-Press the Project Setup tab, and then press the Set Project Default State button.</td>
+Press the Close button in the FARO Arm Utilities window.</td>
 <td>
-[[image:vtube_v2.2_projecttab_saveprojectdefault.png|400px]]
+[[image:vtube-laser_v2.2_armutilities_dialog_press_close.png|400px]]
 </td>
 </tr>

@@ Line 43: / Line 43: @@
 ===STEP 3===
-Press the System Options button.</td>
+Select the correct ball probe then press OK.<br><br>
 <td>
-[[image:Vtube-STEP_v2.2_toolbar_sys.png|400px]]
+[[image:vtube-laser_v2.2_faro_compensation_menu.png|400px]]
 </td>
 </tr>

@@ Line 34: / Line 34: @@
 <td width=300>
 ===STEP 2===
-Change the values in VTube to whatever you want them be when you perform a clear.  Be sure that no tube data exits in this state, or VTube will clear the data to preset values with a tube.  (Of course, you can do this, if you really meant to.)</td>
+Press Probe Setup and Calibration.</td>
 <td>
-[[image:vtube-step_v2.2_cleared.png|400px]]
+[[image:vtube-laser_v2.2_armutilities_dialog_press_probesetup_and_calibration.png|400px]]
 </td>
 </tr>
 <tr>
 <td width=300>
 ===STEP 3===
 Press the System Options button.</td>